As prescribed in 11.204-94 insert the following clause:
MARKING REQUIREMENTS (APR 2008 MARITIME) - DLAD
Marking of Unit, Intermediate and Shipping Containers for Shipment and Storage. Unless authorized by paragraph 7 below, all shipments, regardless of levels specified, including industrial, shall be marked in accordance with the most recent version of MIL-STD-129P (19-SEP-2007), “Marking for Shipment and Storage". In addition to MIL STD-129P requirements, the following instructions also apply:
1. Joint Army-Navy (JAN) and Other Special Markings In Accordance With Government Specifications: As designated, the following marking shall be placed on the unit package (carton, box, bag, etc., used as the initial protection), in addition to normal MIL-STD 129P marking. If the marking space on the MIL-S(JTD-129P identification side of the unit package is too small (3 inches by 4 inches or less surface area) to accommodate this additional marking, the reverse side of the package may be used.
(a) Semiconductor Devices procured under MIL-PRF-19500M:
(1) Part or Identifying Number (PIN)
(2) Manufacturer's ID and symbol
(3) Lot identification code and code of assembly plant (if applicable)
(4) Beryllium oxide identifier (if applicable)
(5) Electrostatic discharge sensitivity identifier (if applicable)
(6) Country of origin
(7) DMS Marking (if applicable)
(b) Microcircuits procured under MIL-M-385 I0J, Notice 1:
(1) PIN
(2) Identification code
(3) Manufacturer's identification
(4) Manufacture's designation symbol
(5) Country of origin
(6) 'JAN' certification mark
(7) Special marking
(8) Electrostatic discharge sensitivity identifier
(c) Other Semiconductor Devices and Microcircuits not procured under a Military Specification
(1) Identification number
(2) Manufacturer's identification
(3) Manufacturers date code
(d) Special marking as required under an applicable Military Specification.
2. Sensitive Electronic Devices: When the MIL-STD-2073-1D, Packaging Requirements Code specifies method of preservation GX or ZZ, with special marking code “39” (ESD Sensitive Electronic Device Requirements), sensitive electronic devices caution marking shall be applied as specified in MIL-STD-129P.
3. Bar Code Marking: Regardless of levels of packaging specified (including Industrial), bar code marking shall be applied to all unit, intermediate, and exterior containers in accordance with MIL-STD-129P.
(a) EXTERIOR CONTAINERS: For DLA contracts, each Exterior shipping containers shall be bar coded with the NSN, contract number (including the call number) and Cage Code.
(b) MULTIPACKS:
(1) Item identification markings. Item identification markings will not be bar coded on the exterior shipping container of multipack shipments. However, unit packs and intermediate containers in the multipack shall be bar coded.
(2) Contract number. Contract number will be bar coded on the exterior shipping container of the multipack if the number applies to all unit and intermediate containers inside the multipack. If mixed contract numbers are contained in the multipack, then the exterior container will not be bar coded.
4. Hazardous Materials: (Performance Oriented Packaging). In addition to the packaging requirements included in the commodity specification listed below, the supplies shall comply with applicable packaging requirements of AFMAN 24-204 (DLAI 4145.3), Preparing Hazardous Material for Military Air Shipments, the International Civil Aviation Organization (ICAO) technical instructions for the safe transport of dangerous goods by air. The International Maritime Dangerous Goods Code (IMDG CODE) and Title Forty-nine of the Code of Federal Regulations (49 CFR). To the extent that there is conflict between the requirements of the commodity specification and other packaging data listed below and the requirements of AFMAN 24-204 (DLAI 4145.3), ICAO, and IMDG CODE, the provisions in AFMAN 24-204 (DLAI 4145.3), ICAO and IMDG CODE will control over the conflicting provisions in the commodity specification and other packaging data. Unless otherwise specified by the procuring activity, interior and exterior containers of hazardous material shall be properly classified, documented, certified, described, packaged, marked, and labeled in accordance with AFMAN 24-204 (DLAI 4145.3), ICAO, IMDG CODE, 49 CFR, and MIL-STD-129P. In addition to the above requirements, the CAGE (Commercial and Government Entity) Code, shall be marked on all unit, intermediate and exterior containers.
5. Exterior Documentation: Packing list as specified in MIL-STD-129P is required.
6. Parcel Post APO/FPO Shipments: The statement "Contents for Official Use. Exempt from Customs Requirements" shall be annotated above the mailing address.
7. Electronics Exclusions: Electron Tubes: These items shall be marked in accordance with MIL-E-75H.
8. WARRANTY MARKINGS: When specified in the contract that the supplies are being required with a warranty agreement, the unit intermediate, and shipping containers shall be marked in accordance with MIL-STD-129P.
(End of Clause)
